專業分析儀

力可ONH836氧氮?dú)浞治鰞x

特點和優勢

國際**的非色散紅外及熱導檢測器 ，無移動部件，不需要手動調整

采用三個**的紅外器檢測氧含量，同時檢測CO和CO2，然后在轉化為CO2集中檢測，原理上是**完善的，所以不僅可以保證中間量程的測量精度，在**含量和高含量的檢測范圍內同樣可以滿足精度要求

高性能的紅外檢測器配置***恒溫絕熱技術，消除了外界環境溫度的干擾

長壽命的紅外發射光源和無漂移的電路設計保證檢測器的長期穩定性

力可**的動態流量補償控制DFC系統，保證了流量系統的完善，可以精確控制整個氣路中的流量，保持流量恒定**改善了材料中氮分析的準確度

可以旁路的OMI-2 氣路強化過濾裝置增強了檢測器的穩定性，使得分析結果更加準確

可選自動功能

20位試樣自動進樣系統

通用下電極坩堝支座，容納各種坩堝使用

無需人工干預的全自動清掃系統

可選六軸可旋轉觸摸屏幕，增強了操作的工效和直觀性。專業分析儀

Procedure – Powder/Chip Samples

Instrument calibration/drift correction.

Add approximately 0.05 g of *** Graphite Powder to a***Graphite Crucible.

Firmly place the crucible on the lower electrode tip or appropriate autoloader position.

Press the Analyze button on the instrument screen,the lower electrode will close and the analysis sequence will start and end automatically.

Repeat steps 3b through 3i a minimum of three times for each calibration/drift standard used.

美國LECO力可氧氮?dú)浞治鰞xONH836（氧氮?dú)渎?lián)測儀）系列硬件部分

特點和優勢

1、爐頭區域LED照明系統

2、爐頭快速拆裝的粉塵過濾裝置

3、裝有自動旁路閥的可快速拆裝氧水捕集裝置

4、**的動態流量補償（DFC）保證熱導池氣體流量、壓力恒定

5、改進的紅外檢測池技術

     新紅外池的恒溫絕熱技術消除了外界環境溫度的干擾

   長壽命的紅外發射光源和無漂移的電路設計保證紅外檢測池的長期穩定

   氧高低雙量程采用3個碳紅外檢測器，同時檢測一氧化碳和二氧化碳，保證準確定量

  6、高效脈沖爐冷卻系統

   強力內循環水冷裝置

   雙直流風扇保證持續冷卻，不受電壓波動的影響

   新電極爐頭設計，提高脈沖爐熱交換效率

  7、全自動分析系統（可選）

   自動清掃裝置

   20位或100位全自動分析系統

   高速全自動真空除塵裝置直接將粉塵排至儀器外部捕集器中，消除環境污染

Oxygen, Nitrogen, and Hydrogen in Refractory Metals

Summary

Titanium is a metal that can be combined with elements such as aluminum, vanadium, molybdenum, and tin to produce high-strength, lowdensity, and corrosion-resistant alloys. Titanium alloys are used by the military, medical devices, sporting goods, and aerospace industries because of these properties, and due to the strict demands of these industries, effort needs to be taken to assure that the material meets the highest of quality standards.

強力內循環水冷裝置。

Summary

The determination of the amount of oxygen, nitrogen, and hydrogen in iron, steel, nickel-, and cobalt-base alloys represents some of the most important quality metrics for these materials. Oxygen is used to create steel from pig iron by removing excess carbon. Oxygen content must be controlled to limit the amount of carbon monoxide that can be formed during solidification which may cause excessive porosity. Nitrogen is considered both an impurity as well as an important alloying agent. Itcan be present as a nitride or interstitially in its gaseous form. Increased nitrogen content is known to increase yield and tensile strength, thus decreasing ductility and formability. Excessive levels may evolve during solidification thus increasing porosity. High hydrogen content is the primary cause of embrittlement, blistering and flaking due to its high

mobility through the lattice and provides no potential alloying benefits. The ONH836 utilizes a high-power

electrode furnace to quickly and efficiently release the target gases from within the sample, which allows

for a very rapid simultaneous determination of oxygen, nitrogen, and hydrogen.

***紅外池的恒溫絕熱技術消除了外界環境溫度的干擾。專業分析儀

可以旁路的OMI-2 氣路強化過濾裝置增強了檢測器的穩定性，使得分析結果更加準確。專業分析儀

氧氮?dú)浞治鰞x是快速、準確分析氧、氮、氫元素的、高性能儀器，整機采用模塊化、一體化設計，即主機由可靠的脈沖電極爐、高靈敏高精度的檢測系統、布局合理和氣密性好的氣路系統、可靠耐用的電源系統、穩定的電路系統、高校節能的水循環散熱系統等六個**的硬件模塊單元組成。

氧氮?dú)浞治鰞x的測量原理：

測量范圍非常***。分析樣品時，樣品被稱重后放到樣品端口中，然后用載氣進行沖洗，防止大氣（含氧氣和氮?dú)猓┻M(jìn)入到爐子系統中。

石墨坩堝在脈沖爐中脫氣，以盡量減少自帶的污染。經過穩定階段后樣品落入坩堝中并熔融。樣品中的氧與石墨坩堝中的碳反應生成一氧化碳。氮和氫以單質的形式釋放。載氣和樣品氣體通過粉塵過濾網后再進入到氧化銅催化爐中，將一氧化碳氧化成二氧化碳。

二氧化碳進入到紅外池中用于測定氧含量，被測后的氣體導入化學試劑管，這時二氧化碳和水被化學試劑除去，氮元素通過熱導檢測池含量被測定。測量氫時，載氣換為氮?dú)?，樣品氣體通過舒茨試劑而不是氧化銅催化劑。測氧和氮時也可采用更廉價的氬氣作為載氣。 專業分析儀